O-Fivecc
01-30-2010, 12:13 AM
This is what I did and it turned out beautifully.
You will need: 1000 and 1500 grit sandpaper, 1 can of VHT Niteshades (got mine at Advanced Auto), I can of clear coat, and some painters tape (if you want to leave the reverse clear lenses untinted).
First, removing taillights: Lower your tailgate, you will notice 2 bolts/screws on the inside where the taillight is. Remove those. Then, pull the taillight straight back toward you. On the front there is 2 clips, and you will want to pull the light back to get it out of the clips. Then just give each bulb harness a 1/2 turn and they should pull right out, then your taillights are free.
Second wet sanding: I did mine in a sink with running water, but a hose or 5 gallon bucket is fine, just keep the sandpaper wet. Using the 1000 grit sandpaper,wet sand the entire surface of light housing that you want painted. Then dry them.
Third, tinting them: Pick a place that does not have a lot of lint, dust, or dirt flying around. Hold VHT can about 5 inches from light housing. Start spraying a couple inches off to the side of the light, then just pass the spray over the light housing. It takes probably about 7 or 8 passes over the light to get the whole thing covered. Make sure each pass that their isn't any "un-tinted" areas or spots that got less tinting. If this happened, then just carefully and lightly spray over that area. Whatever you do, just make sure you are passing the can over the housing and not just pointing and spraying one section.
After the first coat, let sit for maybe 5 minutes, then continually add coats until you reach your desired level of darkness, waiting about 5 minutes between coats.
After they are as dark as you want them, let them sit for about 4 hours. Then take the 1500 grit sandpaper, and again WET SAND over the dried VHT. Wet sand the entire area that you just painted and dry them. Then add clear coat in the same manner you added the VHT, waiting a few minutes between coats.
I put probably 5 coats of VHT and a couple clear coats. You can tape off the reverse lenses and leave them clear if you desire. This is what I did, the reverse lenses are shaded a little lighter then the rest of the light. I also wet sanded and put one coat of VHT on my 3rd brake light. They look so nice in the middle of the day, I will have to get some mid day pics
236237238239
You will need: 1000 and 1500 grit sandpaper, 1 can of VHT Niteshades (got mine at Advanced Auto), I can of clear coat, and some painters tape (if you want to leave the reverse clear lenses untinted).
First, removing taillights: Lower your tailgate, you will notice 2 bolts/screws on the inside where the taillight is. Remove those. Then, pull the taillight straight back toward you. On the front there is 2 clips, and you will want to pull the light back to get it out of the clips. Then just give each bulb harness a 1/2 turn and they should pull right out, then your taillights are free.
Second wet sanding: I did mine in a sink with running water, but a hose or 5 gallon bucket is fine, just keep the sandpaper wet. Using the 1000 grit sandpaper,wet sand the entire surface of light housing that you want painted. Then dry them.
Third, tinting them: Pick a place that does not have a lot of lint, dust, or dirt flying around. Hold VHT can about 5 inches from light housing. Start spraying a couple inches off to the side of the light, then just pass the spray over the light housing. It takes probably about 7 or 8 passes over the light to get the whole thing covered. Make sure each pass that their isn't any "un-tinted" areas or spots that got less tinting. If this happened, then just carefully and lightly spray over that area. Whatever you do, just make sure you are passing the can over the housing and not just pointing and spraying one section.
After the first coat, let sit for maybe 5 minutes, then continually add coats until you reach your desired level of darkness, waiting about 5 minutes between coats.
After they are as dark as you want them, let them sit for about 4 hours. Then take the 1500 grit sandpaper, and again WET SAND over the dried VHT. Wet sand the entire area that you just painted and dry them. Then add clear coat in the same manner you added the VHT, waiting a few minutes between coats.
I put probably 5 coats of VHT and a couple clear coats. You can tape off the reverse lenses and leave them clear if you desire. This is what I did, the reverse lenses are shaded a little lighter then the rest of the light. I also wet sanded and put one coat of VHT on my 3rd brake light. They look so nice in the middle of the day, I will have to get some mid day pics
236237238239